ELNA 6005 Instrukcja Użytkownika Pobierz pdf

ERROR CODES

MODEL(S)

ERROR(S)

Janome model(s):

MB4

Elna models:

940 / 9900

Detailed diagnosing of this machine is very difficult and may require contacting the Janome Service Department. The following are simple checks.

The error ‘E:##’ is displayed on the small LCD on the machine when the RCS is not plugged in. When the RCS unit is plugged in, it will give a specific error on the LCD:

E:00: Please power down and restart again. (Communication error with the RCS. The machine won’t display this error on the RCS. Instead the screen will not go to the next step from the ‘Welcome

screen’.)

1. Check the connection going from the RCS plug into the RCS unit and the connector on the machine to the ‘B’ board.

2. Try another RCS unit to determine which part is the problem.

E:01: Please power down and restart again. (There is a problem with a stepping motor not initializing correctly or at all.)

1. With the machine off, manually move the head to needle #4, push the carriage unit all of the way to the front and to the right. Turn on the machine and see which doesn’t calibrate.

2. While holding down the Start/Stop & Reverse buttons, turn on the machine. Release the buttons once you see icons on the screen:

A. Press “Phase” then ‘All Init’ to calibrate the machine, then press “Cancel”.

B. Check the “Needle” and press the left & right arrow keys to bring the needle to #4 then back to #1 to check the step motor & sensors. Press “Cancel” to exit.

C. Press “Pick-Up” and press “Init” to check the thread catcher. Press “Cancel” to exit.

D. Press “Sensor Solenoid” and press “Solenoid1” to check [QQQQQQ] and “Solenoid2” to check [QQQQQQ]. Press “Cancel” to exit.

E. Press “Cut Motor” and press “Init” to calibrate the dynamic cutter. Now press “Divide” then “Init” once again to check the cutter.

E:02: Please power down and restart again. (Needle bar changeover.)

1. Remove the stationary cover then turn the hand wheel to 270°. Using a 2.5mm hex driver, turn the silver gear on the needle-change step motor to move the head from needle bar #1 to #4 then

back to #1 to check for any binds. If there is a bind, adjust ‘head play’ as shown in the service manual.

2. Check and adjust ‘moving head stop position’ and ‘needle stop position’ as shown in the service manual.

E:03: Needle bar is out of position. Press OK to move the needle bar to switching position. (Needle bar change over phase.)

3. Remove the stationary cover then turn the hand wheel to 270°. Using a 2.5mm hex driver, turn the silver gear on the needle-change step motor to move the head from needle bar #1 to #4 then

back to #1 to check for any binds. If there is a bind, adjust ‘head play’ as shown in the service manual.

4. Check and adjust ‘moving head stop position’ and ‘needle stop position’ as shown in the service manual.

E:04: Lock!!. (There is a problem with the DC Motor.)

1. Clean the sensor on the DC motor and check if the shield plate on the motor is not loose or hitting the sensor. If either the sensor or shield plate is damaged, replace the motor.

2. Try resetting the DC motor. Hold down the Forward & Bobbin Winder buttons on the RCS unit then turn on the machine. Press the button called “Clear”. Turn off the machine.

E:05: Rethread and start. (Either the machine broke the thread or it thinks the thread is broken.)

1. Remove any thread, then the tension unit cover. Now run the machine and quickly spin the small wheel by hand (depending on which needle is being ‘sewn’). If it still gives you the error, check

the connections or replace the circuit board.

2. If you do not get the error, check: needle position (left-right & front-back), needle bar height, presser bar height, hook timing, and clearance.

E:06: [Deleted]

E:07: Please power down and restart again. (The thread cutter malfunctioned.)

1. Check the connections and any binds in the thread cutter linkage. Replace the dynamic thread cutter unit if necessary.

E:08: Pull the tension release lever. (The lever that opens the tension discs may be engaged.)

1. Make sure the lever is not engaged (keeping the tension discs open) and check the connections.

2. Remove the tension unit cover and check the position of the microswitch. Adjust the position of this microswitch. Replace the microswitch if necessary.

E:09: Please power down and restart again. (The driving motor malfunctioned.)

Replace DC Motor

1. While holding down the Bobbin Winder & Forward buttons on the RCS, turn on the machine.

2. Once a menu appears on the screen, release the buttons. Press ‘Clear’.

3. Turn the machine off then back on like normal.

Janome model(s):

MC15000

Raise Presser Foot and Needle Bar, then turn power on again.

1. Turn the machine off and attach the carriage unit.

2. Raise the needle bar to the highest position and push the needle bar to the left.

3. Open the embroidery arm and push the carriage all of the way out towards the back and to the left.

4. Put your ear up the machine and then turn it on. Listen for which step motor ‘stutters’ or does not calibrate. Follow the service book to adjusting/replacing the specific unit.

1 2 3 4 5 6 ... 12 13

ERROR CODES 1

Podsumowanie treści

Strona 1 - ERROR CODES

ERROR CODES MODEL(S) ERROR(S) Janome model(s): MB4 Elna models: 940 / 9900 Detailed diagnosing of this machine is very difficult and may require cont

Strona 2

1. Replace the foot controller. 2. Clean the lower shaft sensor and make sure the shield plate going thru this sensor is not hitting the sides of the

Strona 3

E4: Needle Plate Step Motor. A. Check the connections. B. Remove the needle plate and see, press the center needle, straight-stitch needle positions.

Strona 4

Elna model(s): 6005 / 6003 A3. If you do not get an error, switch the zigzag step motor & feed step motor connections on the ‘A’ board. A4. Raise

Strona 5

Elna model(s): 6200 / 5300 / 5200 / 5100 / 520, and many more… A. Check the connections. B. With the machine off, and the presser foot up, push the t

Strona 6

Warning (with a picture showing you to attach the needle plate): 1. The needle plate is not attached properly. 2. The needle plate micro switch needs

Strona 7

Elna model(s): 9600 / 9500 3. Push the needle bar to the left. 4. Open the face plate. Lower the needle threader only half-way down by manually turnin

Strona 8

1. The buttonhole lever is not lowered all the way before sewing a buttonhole. 2. The shield plate is not in the center of the sensor. 3. The buttonho

Strona 9

If you do not see any error number on the lower-right or lower-left section of the error screen, perform the following: 1. Turn the machine off. 2. Ra

Strona 10

If the lever is already down and you get this message perform the following: 1. Remove the face plate, remove any foot on the machine, and pull down t

Strona 11

E7: The customer pressed the thread cutter button too many times. The thread cutter can only be used up to 3 times in a row. Once the machine sews se

Strona 12

Elna model(s): 6004 2. Check the connections. Make sure the white cover over the pins on the ‘A’ board. Sometimes the white cover will cover the pins

Strona 13

MC5700 A. Check the connections. B. With the machine off, push the needle bar to the left & right several times. You should just feel the friction

Komentarze do niniejszej Instrukcji

Brak uwag

ELNA 6005 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Maszyny do szycia ELNA 6005. Janome & Elna Error Code List (Updated 10/16/2014) Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Maszyny do szycia ELNA 6005